U.S. Fire Marshal Hood Inspections: Separate Cleaning From Suppression

Inspector examining a commercial kitchen hood

NFPA 96 ties hood and duct cleaning frequency to how much you cook. Confirm suppression-system inspection intervals with your local fire marshal and qualified contractor. Your fire marshal, acting as the authority having jurisdiction, enforces both. Keep service tags, cleaning receipts and inspection records on-site, because an inspector will ask for them before looking at anything else.


TL;DR:

  • NFPA 96 calls for monthly cleaning with solid fuel, quarterly cleaning for high volume kitchens, and annual cleaning for low volume kitchens; confirm moderate volume locally.
  • Suppression systems are inspected every six months, while cylinder hydrostatic testing and internal examinations follow separate, longer service cycles; confirm local requirements.
  • Contractors check nozzle aim and caps, fusible links, cylinder weight and pressure, shutoffs, manual pull stations, alarms, and required records.
  • A compliant cleaning covers the hood, filters, plenum, full ductwork, access panels, and rooftop fan; a suppression service tag alone does not prove cleaning.
  • Before inspection, gather service reports, cleaning receipts, tags, and nozzle maps, clear rooftop and duct access, and arrange witnessed tests outside peak hours.

Alldaypowerwashing
Keep Kitchen Hoods Clean
All Day Power Washing provides kitchen hood de-greasing for restaurants in Colorado Springs and the Denver metro area.

Table of Contents

Who enforces your hood inspection and why local rules matter

The authority having jurisdiction, usually your fire marshal or fire prevention bureau, decides whether your exhaust and suppression systems are acceptable. NFPA 96 sets the baseline, but your local office applies it and can add amendments. The National Restaurant Association advises operators to confer with their local fire marshal to understand those amendments, since they change how inspections are documented and enforced.

Here is what the authority typically handles:

  • Plan review and permits: New hoods, relocated cooking lines and suppression changes often need approval before work starts.
  • Submittals: Some offices want stamped plans or nozzle layouts for new installs and alterations.
  • Witnessed tests: For new or altered systems, an inspector may need to watch an actuation or shutoff test.
  • Final acceptance: Nothing is signed off until the office accepts the work and paperwork.

Call your fire marshal’s office early to confirm local amendments and scheduling lead times.

How often to inspect and clean under NFPA 96

Suppression-system inspection intervals should be confirmed with your local fire marshal and qualified contractor. Those intervals do not change with your menu or volume. NFPA 96 ties cleaning frequency to cooking volume, and inspections of the exhaust system determine whether cleaning is needed to prevent dangerous grease buildup.

Use these cleaning bands to set your calendar:

  • Solid-fuel cooking: monthly
  • High-volume cooking: quarterly
  • Moderate-volume cooking: confirm the appropriate cleaning frequency with your local fire marshal.
  • Low-volume cooking: annual

Per NFPA 96, cleaning frequency follows cooking volume. Confirm the suppression-system inspection schedule with your local fire marshal and qualified contractor. Keep cleaning and suppression inspection schedules distinct.

Cylinder service has its own long-interval items, such as hydrostatic testing and internal examination of agent cylinders. Your licensed contractor tracks those dates and should tell you when they come due. If you run a high-volume fryer line, assume your cleaning interval is shorter than your neighbor’s grill-only kitchen.

What a suppression system inspection checks

A licensed contractor works through the system component by component. Knowing the list lets you spot problems before the inspector does.

  1. Nozzles: They must be aimed at the appliances they protect, fitted with intact caps and free of grease or obstruction.
  2. Fusible links: Each link is checked for condition and replaced according to the applicable service schedule, since grease buildup can keep a link from releasing.
  3. Agent cylinders: Technicians verify weight and pressure and note upcoming hydrostatic or internal service dates.
  4. Shutoffs and interfaces: Gas valves and electrical shutoffs must trip when the system fires, and the manual pull station and any alarm connection get tested.
  5. Paperwork: Expect a nozzle coverage map, fusible link serial numbers, cylinder weight and pressure readings, a fresh service tag and a report formatted the way your AHJ wants it.

Pro Tip: Ask your contractor to leave a copy of the nozzle map and link serials in your binder, not just the tag on the cylinder.

Hood, plenum and duct cleaning and how it ties to compliance

Cleaner removing grease from hood plenum

Cleaning is a separate obligation from the suppression inspection. A tag on the suppression cylinder does not prove the hood and ducts were cleaned, and inspectors look at both.

A compliant full-system clean covers more than what you can see from the cook line:

  • Hood and filters: degreased inside and out, with filters cleaned or swapped
  • Plenum: the chamber above the filters, where grease collects out of sight
  • Ductwork: the full run, including access panels
  • Rooftop exhaust fan: the last stop for grease, and often skipped in surface-only jobs

Surface-only cleaning leaves the grease that actually feeds a duct fire. Cleaning records back up your suppression paperwork, because they show the system stays cleanable between inspections. Choose contractors who follow NFPA 96 and IKECA best practices. Our guide on grease duct cleaning requirements covers the scope in more detail, and this guide to why restaurant kitchens need duct cleaning makes the same case from another angle.

A pre-inspection checklist to complete before the inspector arrives

Most failures come from missing paperwork or blocked access, not from broken equipment. Work through these steps before the inspector arrives:

  1. Pull your records: current suppression service reports, cleaning receipts, service tags and nozzle maps, in one binder.
  2. Clear access: make sure the rooftop fan, duct access panels and cylinder area can be reached safely.
  3. Check the shutoffs: gas and electrical shutoffs should be labeled and operable.
  4. Verify your provider: confirm the contractor is licensed and write their credentials into your records.
  5. Plan for witnessed tests: if the AHJ wants to see actuation, arrange brief downtime or a staged check so service is not disrupted at peak hours.

Pro Tip: Keep a one-page cover sheet listing the last service date for each item, so the inspector can verify everything efficiently.

What happens after inspection: tags, reports and enforcement

After a passing inspection you receive an updated service tag, and often a certificate of completion or an AHJ-formatted report listing the work done and system condition. File them with your cleaning receipts.

A failed item is not the end of the road. Deficiencies get documented, corrected and re-tested. Common ones include:

  • Clogged or misaimed nozzles
  • Low agent pressure or weight
  • Heavy grease in the hood, plenum or ducts
  • Missing or expired tags

If problems go uncorrected, your fire marshal can issue notices, fines or stop-work orders, and your insurer may scrutinize a claim when records are missing or come from an unlicensed provider. Treat the re-test as a deadline, not a suggestion.

Why qualified cleaning and good records prevent failures

Inspectors accept evidence, not promises. A full clean from hood to rooftop fan, backed by a written report, shows that your system can be inspected and kept clean. Contractors who follow NFPA 96 and IKECA practices supply what an inspector expects:

  • Tags and dated reports for every service visit
  • Nozzle maps and testing records that match the installed system
  • Before and after documentation showing cleaned surfaces

We handle kitchen hood degreasing in Colorado Springs and the Denver metro area as a fully insured crew. Suppression inspections stay with your licensed suppression contractor, and we coordinate our cleaning dates around theirs.

Treat inspection readiness as a habit

I treat hood compliance as an ongoing routine, not an annual scramble. If you do not have your suppression inspection on the calendar, confirm the required interval with your local fire marshal and book it. Put cleaning and inspection into a service agreement, keep a digital logbook of every visit, and call your fire marshal early for local guidance.

— Brandon

Get an inspection-ready hood cleaning from our crew

Before your next inspection, we can provide kitchen hood degreasing. Quotes are available, and our work comes with a satisfaction guarantee. Request a quote for kitchen hood degreasing and tell us your cooking volume, and we will help you plan a cleaning schedule that fits your inspection dates.

Alldaypowerwashing

FAQ

How often should a hood system be inspected?

Suppression systems are inspected every six months under NFPA 96. Cleaning frequency is separate and depends on cooking volume, from monthly for solid-fuel cooking to annually for low-volume kitchens.

Does the fire marshal do inspections?

Yes, the fire marshal or fire prevention office acts as the authority having jurisdiction and can inspect your hood and suppression system. Licensed contractors do the technical service, and you present their records. Confirm local expectations with your office, as the National Restaurant Association recommends.

What records should I have ready for an inspector?

Keep your current suppression service report, service tags, nozzle map and cleaning receipts together. Add your contractor’s license details so the inspector can verify who did the work.

How much is a fire marshal inspection?

Fees vary by jurisdiction, and we do not have a standard figure to quote. Call your local fire marshal’s office for its fee schedule, and ask your licensed contractor what the scheduled service costs.

Sources